Tape won't load.

When loading a tape I get a loud clicking noise.

★ ★ ★ ★ ☆ 4.0 stars


Product Troubleshooting for EWV603 VHS VCR

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Answers :

This is a problem with the process called 'tape loading' - pulling the tape loop out of the cassette and wrapping it around the spinning video drum, engaging the capstan and pinch roller and reel rotation. With the cover off, observe the behavior when you hit play. (You may need to put a piece of cardboard over the cassette to block external light from interfering with the start/end tape sensors). Assuming this is a basic VCR (no instant start features), you should see: 1. The video head drum begins to spin. 2. the roller guides move smoothly on the tracks, wind the tape around the drum, and stop snuggly pressed against the 'V-stopper' at the end of the tracks. 3. The pinch roller moves into position and presses the tape against the capstan. 4. The tape begins to move and is wound up by the takeup reel. 5. The picture and sound appear on the TV. With a 'rapid or quick start' (or it may be called something else) transport, the tape moves to a half-loaded position when the cassette is inserted. This is at an intermediate position partially pulled out of the cassette but not wrapped around the drum. On VCRs with a real-time counter and/or index search capabilities, the tape will be in contact with the control head. With an 'instant start' transport, the tape will fully load around the spinning drum when the cassette is inserted but the capstan will not engage and no tension will be applied to the tape until you press PLAY or REC. (After about 5 minutes, the drum will stop and it may unload to the half loaded or unloaded position.) Note that for VCRs with a real-time counter and/or index search capabilities, the tape must be in contact with the control head (but not the video heads) for all relevant modes. These VCRs (which include many modern units) must therefore pull the tape at least partly out of the cassette. In all cases, the completion of the sequence results in approximately the same mechanical configuration during PLAY. Several likely possibilities when it shuts down: 1. Everything occurs as above, picture and sound appear for a few seconds, but then the VCR unloads the tape, ejects the cassette, goes into REW mode, stops, or shuts off. Two common causes: The takeup reel does not turn and tape spills into the machine. This is sensed by the microcontroller which aborts record or play and attempts to save your valuable cassette. Most likely cause: old/dirty idler tire. As a test, turn the idler tire inside-out. The fresh surface will now work well enough to confirm this diagnosis and will continue working long enough for your replacement idler tire to arrive. See the section: "General guide to VCR cleaning and rubber parts replacement". The takeup reel is turning properly but one of the reel The takeup reel is turning properly but one of the reel rotation sensors or its electronics is defective. As a test, check to see if the tape counter is changing at any time during the loading and
FixYa.com is the worst web site there is

Research, Knowledge and Information :

the tape won't load in my cony video 8 handycam cc... - the ...

the tape won't load in my cony video 8 handycam ccd=fx730v
Read More At : community.sony.com...

tr70 tape won't load - the Community

CDC Tr70 will not load tape. when tape inserted and door pushed closed , tape whirls for a while then door ejects without loading tape. . door closes
Read More At : community.sony.com...

Sony HVR-V1u Won’t Load Tape Error Code C 32:11

Sony HVR-V1u Won’t Load Tape Error Code C 32:11. ... Problems occur when it will not load down or latch and is stuck in the fully ejected or unloaded position.
Read More At : www.videoonerepair.com...

HELP -- tape won't load XH-A1 | Videomaker.com

The tape symbol in the top right corner of the display was also flashing red. ... *** HELP -- tape won't load XH-A1. southernhunter. Last seen: 7 years 2 weeks ago
Read More At : www.videomaker.com...

JVC VCR won't load tapes | Electronics Forums

JVC VCR won't load tapes. Discussion in 'Electronic Repair' started by John Z., Jun 16, ... load the tape (which it won't because the transport locks up) and then
Read More At : www.electronicspoint.com...

Sony SL-C40 Betamax VCRs won't load tapes, need help to fix ...

Aug 28, 2013 · I have a couple of Sony SL-C40ES Betamax VCRs which I want to repair, both have the same fault, I try to put a tape in, the tape won't go right in and gets ...

Sony camcorder, cassette won't load in - Computing.Net

Sony camcorder, cassette won't load in. Tags: Sony. Camcorders. Ermine November 13, 2014 at 18:15:46 ... VCR's use infrared sensors to determine if a tape is in.
Read More At : www.computing.net...

Not a bug - Holo tape won't load | Sim Settlements

Not a bug Holo tape won't load. Discussion in 'Bug Reports' started by Spacer, Jul 7, 2017 at 12:51 PM. Tags: bug; xbox1; Spacer New Member. Messages: 3 Likes Received: 1
Read More At : simsettlements.com...

Having problems with your EWV603 VHS VCR ?

Loading ...

Load time: 0.0437 seconds